CT150 Fuel Injector Cleaner & Tester

The CT150 model is an integrated four-cylinder fuel injector machine launched by AUTOOL in 2018. It combines ultrasonic cleaning technology and microcomputer oil pressure closed-loop control technology into one, which can simulate various working conditions of the engine and can clean and test the injectors of automobiles and motorcycles. It has a three-dimensional and nice appearance, which is both drop-resistant and shockproof. It has undergone years of technological and design innovation in which it will solve your fuel injector problems with stable performance and convenient operation.

It is an expert in Injector solutions, featuring 12 injector-specific functions

  1. Ultrasonic cleaning: It sends signals to the injectors through the pulse signal line, using the cleaning fluid with the ultrasonic vibration so as to completely remove the carbon and impurities inside the injectors.
  2. Idle speed test (0-20ms): Simulate the engine idling speed and test the state of the fuel injector.
  3. Medium speed test (0-7.5ms): simulate the engine running at medium speed and test the state of the fuel injector.
  4. High-speed test (0-4ms): Simulate the high-speed performance of the engine and test the state of the fuel injector.
  5. Acceleration test: Simulate the acceleration state of the car and test the performance of the fuel injector.
  6. Shift speed test: Simulate the shifting state of the car and test the working performance of the fuel injector.
  7. Leakage test: Test the sealing condition of the fuel injector.
  8. Idle dpeed sprayability Test: Simulate the engine idling state and test the spraying performance of the fuel injector.
  9. Medium speed sprayability test: Simulate the engine medium-speed state and test the spraying performance of the fuel injector.
  10. High-speed sprayability test: Simulate the high-speed state of the engine and test the spraying performance of the fuel injector.
  11. Reverse flush: Reverse flush is a way to clean the injectors with the test liquid flowing from the outlet to the inlet of the injector. Reverse flush may remove the dirt inside the injector or the injector Strainer (Only for the top fuel supply injector).
  12. No-disassembly cleaning: Direct cleaning without disassembling the injectors, this function is an additional function, which requires special adapters.

Full inspection of injectors

  • Uniformity test: To test the uniformity of injecting amount of each injector.
  • Sprayability test: To monitor the spraying status of each injector with the help of backlight.
  • Leakage test: To test the sealing and dribbling conditions of injectors under high pressure.
  • Injecting flow test: To check the injecting amount of the injector of specific injection condition(eg. same time and number of times).
  • Support 110V/220V supply voltage; support simultaneous cleaning and testing of 4-cylinder injectors; support testing of standard injectors for automobiles and motorcycles.

Cleaning fluid recovery valve

After the cleaning is completed, the cleaning fluid needs to be recovered through the valve, which has the advantage of:

  1. Damage will be caused to the product of the liquid is left inside the cleaning bath for a long time.
  2. The recovered liquid can be reused, thus saving your cost.

Test level gauge

It allows you to observe the amount of test fluid. If too much or too little is added, it will affect the result of the test.

Pressure gauge

It allows you to observe the pressure during test to avoid damage to machine or injectors caused by excessive pressure.

How to choose test fluid?

The test fluid is used to test and judge whether the performance of the fuel injector is in good condition. It is a colorless and transparent liquid with no irritating odor, non-corrosive, and not easy to emit. Its function is to simulate various working states of the fuel injector as a medium. In order to achieve the best test effect, it is recommended to use professional automotive injector test fluids. If it is not available locally, as an alternative, it\'s recommended that medical alcohol with an alcohol content of more than 75% can be used instead of the test fluid.

How to choose cleaning fluid?

Cleaning fluid is used to clean deposits (such as carbon deposits) on fuel injectors, and it is usually highly corrosive and flammable. In order to achieve the best test effect, it is recommended to use professional injector ultrasonic cleaning fluid. If it is not available locally, it\'s recommended that medical alcohol with an alcohol content of more than 75% can be used instead of the cleaning fluid, but note that the effect may not good enough.

How does the CT150 work?

Ultrasonic Cleaning:

  1. Add the cleaning fluid and put the injectors into the ultrasonic cleaning bath.
  2. Connect the pulse signal lines and select the item 1 Ultrasonic Cleaning function to start.

Injector Testing

  1. First add the test fluid, then install the injectors on the fuel distributor, and fix them with bolts.
  2. Different functions can be selected to test to see if any of the injectors are leaking or blocked.

Working conditions

  • Power supply: AC220V/AC110V±10%
  • Frequency: 50HZ±0.5
  • Humidity: <85%
  • Ambient temperature: 0℃~+40℃
  • Magnetic field: <400A/m
  • Power: 50W.
  • Ultrasonic cleaning bath size: 150mm x 84mm x 64mm
  • Sparks and open flames are prohibited.

Packing list:

  • 1pcs * AUTOOL CT150 Fuel Injector Cleaner Tester Main Unit;
  • 1pcs * Funnel(for adding test fluid);
  • 1pcs * Ultrasonic Cleaning Bracket(for placing the injectors during cleaning);
  • 1pcs * Drain Valve(For recover the cleaning fluid );
  • 2pcs * Fixing Bolt(For fixing the oil separator);
  • 2pcs * Fixing Nuts(For fixing the oil separator);
  • 4pcs* Reverse flush connectors φ15.8mm(for connecting the bottom of the injector and the oil separator hole)
  • 4pcs * Conical top inlet connectors φ10.5mm&13.6mm (for connecting the top of the injector and the oil separator hole)
  • 4pcs *Adapter cables(For transferring the pulse signal line connector, instead of connecting the injector signal input pin)
  • 1pcs * Power Cable(for connecting power supply);
  • 1pcs * Oil Separator(Distribution device for outputting pressurized test fluid to the injectors);
  • 4pcs* Special injector gaskets(for auxiliary installation of special fuel injectors)
  • 3pcs * Special plugs for oil separator(used to block the holes on the oil separator)
  • 1pcs * Ultrasonic Cleaning Cover(for keeping the cleaning bath clean)
  • 1pcs * User Manual(Instructions)